Tyan B8226G24V4H Spezifikationen

TYAN GT24 B8226 Service Engineer’s Manual

10 http://www.tyan.com · Do not place objects on AC power cords or cables. Arrange them so that no one might accidentally step on or trip over them.

11 http://www.tyan.com · Allow the product to cool before removing covers and touching internal components. · Remove all watches, rings, or loose je

12 http://www.tyan.com

13 http://www.tyan.com Table of Contents Chapter 1: Overview... 15 1.1 About t

14 http://www.tyan.com 3.4.3 Removing the Motherboard ... 60 3.5 Replacing the Slim DVD-ROM (optional)

15 http://www.tyan.com Chapter 1: Overview 1.1 About the TYAN GT24-B8226 Congratulations on your purchase of the TYAN® GT24 B8226, a highly opti

http://www.tyan.com 161.3 Features B8226G24V4H Form Factor 1U Rackmount Chassis Model GT24 Dimension (D x W x H) 25.4" x 17.2" x 1.72&qu

17 http://www.tyan.com Feature Plug and Play (PnP) /PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot / ACPI 2.0 power management /Power on mode after power recover

18 http://www.tyan.com Port Q'ty (3) LAN Controller Intel 82574L / Intel 82576EB Connector type D-Sub 15-pin Resolution 1600x1200@60Hz Graphi

http://www.tyan.com 191.4 Standard Parts List This section describes GT24-B8226 package contents and accessories. Open the box carefully and ensur

2 http://www.tyan.com

http://www.tyan.com 201.4.2 Accessories If any items are missing or appear damaged, contact your retailer or browse to TYAN®’s website for servic

http://www.tyan.com 211.6 About the Product The following views show you the product. 1.6.1 System Front View 1.6.2 System Rear View

http://www.tyan.com 221.6.3 LED Definitions Front Panel LED State Color Description On Green System is turned on Blinking Green System is

http://www.tyan.com 23ID LED LED State Color Description On Blue System identified ID LED Off Off System not identified HDD LED HDD Status

http://www.tyan.com 241.6.4 Motherboard (S8226) Layout The diagram is representative of the latest board revision available at the time of publi

http://www.tyan.com 251.6.5 Jumpers & Connectors Jumper/Connector Function J4 COM2 Header J5/J12/J30/J34/J54/J55/J56 4-pin Fan Connectors J1

http://www.tyan.com 261.6.6 System Block Diagram

http://www.tyan.com 271.6.7 Internal View 1 HDD Cage 2 M1232/M1235 HDD Backplane 3 System Fans 4 500W Power Supply 5 Memory Slots 6 CPU Sockets

http://www.tyan.com 28NOTE

http://www.tyan.com 29Chapter 2: Setting Up 2.0.1 Before you Begin This chapter explains how to install the CPUs, CPU heatsinks, memory modules,

3 http://www.tyan.com PREFACE Copyright This publication, including all photographs, illustrations, and software, is protected under inte

http://www.tyan.com 302.0.4 Precautions Components and electronic circuit boards can be damaged by discharges of static electricity. Working on a

http://www.tyan.com 312.1 Installing Motherboard Components This section describes how to install components on to the mainboard, including CPUs,

http://www.tyan.com 322.1.2 Installing the CPU and Heatsink Follow the steps below on installing CPUs and CPU heatsinks. 1. Locate the CPU soc

33 http://www.tyan.com 5. Place the CPU into the socket and make sure that the gold arrow is located in the right direction. 6. Close the CPU sock

34 http://www.tyan.com 7. Position the heatsink on top of the CPU and secure it with 2 screws. 8. Repeat the procedures mentioned earlier to insta

http://www.tyan.com 352.1.3 Installing the Memory Follow these instructions to install the memory modules onto the motherboard. 1. Locate the

36 http://www.tyan.com

37 http://www.tyan.com Recommended Memory Population Table R-DIMM Module Support DDR3 Speed/Voltage DDR3 Rank Configuration 1.35v 1.5v DIMM0 (A0,

38 http://www.tyan.com Single-Rank & Dual-Rank Memory Module Single CPU Installed (CPU0 only) Dual CPU installed (CPU0 and CPU1) Quantity of m

39 http://www.tyan.com Single-Rank, Dual-Rank & Quad-Rank Memory Module Single CPU Installed (CPU0 only) Dual CPU installed (CPU0 and CPU1) Quan

4 http://www.tyan.com FCC Declaration Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: T

40 http://www.tyan.com U-DIMM Module Support DDR3 Speed/Voltage DDR3 Rank Configuration 1.35v 1.5v DIMM0 (A0, B0) DIMM1 (A1, B1) DIMM2 (A2, B2) Max

http://www.tyan.com 41 Single CPU Installed(CPU0 only) Dual CPU Installed (CPU0 and CPU1) Quantity of memory installed 1 2 4 2 4 6 8 CPU0_DIM

http://www.tyan.com 422.1.4 Installing Hard Drives The GT24-B8226 supports four 3.5” hard drives. Follow these instructions to install a hard driv

43 http://www.tyan.com 5. Use 6 HDD screws to secure the HDD. 6. Reinsert the HDD tray into the chassis and press the locking lever to secure the

http://www.tyan.com 442.1.5 Installing the PCI-E Cards The GT24-B8226 supports one PCI-E expansion slot. Follow these instructions to install the

http://www.tyan.com 453. Release the screws on both sides of the riser card bracket as shown. 4. Remove the PCI-E cover shields from the chassis.

46 http://www.tyan.com 6. Screw the PCI-E cards firmly to the riser card bracket.

http://www.tyan.com 477. Secure the riser card bracket to the chassis with two screws. 8. The installation of PCI-E expansion card is now complete

http://www.tyan.com 482.2 Rack Mounting After installing the necessary components, the TYAN GT24-B8226 can be mounted in a rack using the supplied

http://www.tyan.com 492.2.2 Installing the inner Rails to the Chassis 1. Screw the mounting ear to each side of TYAN GT24-B8226 as shown using

5 http://www.tyan.com About this Manual This manual provides you with instructions on installing your TYAN GT24-B8226. This Manual is intended for e

http://www.tyan.com 502.2.3 Installing the Outer Rails to the Rack 1. Measure the distance between inner side of the front and rear mounting b

51 http://www.tyan.com M ount ing B ra cke t

http://www.tyan.com 522.2.4 Rack mounting the Server 1. Draw out the middle rail to the latch position. 2. Lift the chassis and then insert

http://www.tyan.com 534. Secure the mounting ears of chassis to the rack with 2 M5-15L(C) screws. NOTE: To avoid injury, it is strongly recommend

http://www.tyan.com 54NOTE

http://www.tyan.com 55Chapter 3: Replacing Pre-Installed Components 3.1 Introduction This chapter explains how to replace the pre-installed compo

http://www.tyan.com 56 Front ComponentsChassis cover DVD ROM (optional) PCBs FAN M1008 LED Control Board M1232/M1235 HDD Backplane

http://www.tyan.com 573.3 Removing the Cover Before replacing any parts you must remove the chassis cover first. Follow Chapter 2.1.1 to remove th

58 http://www.tyan.com 2. Unscrew the M2091 riser card. 3. Unscrew the M2091-R riser card. 4. Install a new riser card onto the bracket followin

http://www.tyan.com 593.4.2 Disconnecting All Motherboard Cables Before replacing the motherboard or certain components, remove cables connecte

6 http://www.tyan.com Safety and Compliance Information Before installing and using TYAN GT24-B8226, take note of the following precautions: ·Read a

http://www.tyan.com 603.4.3 Removing the Motherboard After removing all of the aforementioned cables, follow the instructions below to remove the

http://www.tyan.com 613.5 Replacing the Slim DVD-ROM (optional) Follow these instructions to replace the slim DVD-ROM. 1. Remove the power and da

http://www.tyan.com 624. Disconnect the power and data cables from the DVD-ROM drive. 5. Remove two screws that secure DVD-ROM drive to the brac

http://www.tyan.com 633.6 Replacing the LED Control Board Follow these instructions to replace the M1008 LED control board. 1. Remove the two scr

http://www.tyan.com 643. Remove three screws securing the LED control board to the bracket. 4. Lift the LED control board free from the chassis. A

http://www.tyan.com 653.6.1 M1008 LED Control Board Features M1008 Front Panel Board (FPB) to S8226 M1008 Connect to S8226 Control Cable J3 →

http://www.tyan.com 663.7 Replacing the System Fan Follow these instructions to replace the cooling fans in your system. 1. Locate the cooling fa

67 http://www.tyan.com 40x28mm Fan Step A Step B 4. Follow Step C & D to take out the old fan and replace with a new one. 40x28mm Fan Step C

http://www.tyan.com 685. After replacing the new fans, follow Step A & B in reverse order to lock the fans. Reinstall the fans into the chassi

69 http://www.tyan.com

7 http://www.tyan.com Safety Information Retain and follow all product safety and operating instructions provided with your equipment. In the event o

http://www.tyan.com 703.8 Replacing the M1232/M1235 HDD Backplane 1. Disconnect the power cables connected to the HDD Backplane. 2. Disconn

http://www.tyan.com 713. Remove the three screws securing the bracket to the chassis base. 4. Lift the bracket up from the chassis. 5.

http://www.tyan.com 72 M1232/M1235 SATA/SAS Backplane to S8226WGM3NR Cable SATA/SAS BP Board Connect to S8226 MB Mini-SAS Cable J39 → J17 (SAS 0 ~ 3

http://www.tyan.com 733.8.1 M1232/M1235 HDD Backplane Features M1232 Front View PW1 J5PW2J18 J15J41J7 J39: Mini SAS Connector CtJ40 FAN6 FAN5 FAN

http://www.tyan.com 74M1235 Front View PW1J7: Fan Header PW2J42J18J45J41: SGPIO J39: Mini SAS ConnectorJ40 FAN6 FAN5 FAN4 FAN3FAN2FAN1FAN7J43 J15: CP

http://www.tyan.com 75M1232/M1235 Rear View J14 (HDD3)J13 (HDD2)J11 (HDD1)J10 (HDD0)LED2 LED1LED4 LED3LED6 LED5LED8 LED7

http://www.tyan.com 763.8.2 M1232/M1235 Connector Pin Definitions PW1 Pin 1 2 3 4 Definition+12V GND GND +5V PW2 Definition Pin Pin Defi

77 http://www.tyan.com J40 PWM Control Jumper Pin Definition 1 CPU_PWM 2 PWM_12 3 CPU_PWM2 Pin 1-2 closed: (Default) J43 SGPIO Jumper Switch Pin De

http://www.tyan.com 783.9 Replacing the Power Supply 1. Disconnect the power cables from the motherboard and the M1232. PSU to M1232/M1235 Bac

79 http://www.tyan.com PSU to S8226 MB Power Supply Unit (PSU) Connect to S8226 2x12P PWR P1 → J18 2x4P PWR P2 → J26 2x4P PWR P7 → J52 PSMI P8 → J31

8 http://www.tyan.com · Ensure that the voltage and frequency of your power source match the voltage and frequency inscribed on the electrical rating

80 http://www.tyan.com 3. Remove the power supply bracket and then slide out the whole power supply unit. 4. Install a new power supply unit foll

http://www.tyan.com 81Appendix I: Cable Connection Tables 1. System Fan Connector System Fan to M1232/M1235 Backplane (BP) Board System Fan Connec

http://www.tyan.com 824. Power Supply Cables PSU to S8226 MB Power Supply Unit (PSU) Connect to S8226 2x12P PWR P1 → J18 2x4P PWR P2 → J26 2x4P PWR

http://www.tyan.com 83Appendix II: FRU Parts Table GT24-B8226 FRU Parts Item Model Number Part Number Picture Quantity Description Power Supply CP

http://www.tyan.com 84NOTE

http://www.tyan.com 85Appendix III: Technical Support If a problem arises with your system, you should first turn to your dealer for direct support

http://www.tyan.com 86Returning Merchandise for Service During the warranty period, contact your distributor or system vendor FIRST for any product p

9 http://www.tyan.com · Make sure the full weight of the rack rests on the leveling jacks. · Always load the rack from the bottom up. Load the heavi